Please Leave Us A Message
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Characteristics of TC4(GR5) titanium alloy rod!
TC4(GR5) titanium alloy bar has high strength, corrosion resistance, good low temperature performance and light weight characteristics. The tensile strength of TC4 titanium alloy bar σb ≥ 895MPa and the predetermined residual elongation stress σr0.2 ≥ 825MPa show its high strength characteristics. This high strength enables TC4 titanium alloy bars to maintain structural stability and reliability when subjected to large loads. In addition, TC4 titanium alloy bar has good...
What are the features and advantages of titanium fittings? Where are titanium fittings used?
Titanium Material in titanium fittings has stable chemical properties and good biocompatibility, corrosion resistance and stability, it is a metal that has no effect on people's body and does not cause overreaction. The characteristics of titanium fittings are mainly reflected in the following aspects: 1. Corrosion resistance The corrosion resistance of titanium fittings is relatively high, even when working in humid air and seawater media, its corrosion resistance is significantly higher than...
Comparison of Titanium Alloy and Aluminum Alloy Properties and Application Selection
As two common metal materials, titanium alloys and aluminum alloys play an important role in industry, aviation and other fields. However, they have significant differences in density, strength, melting point, corrosion resistance, process performance, magnetic and electrical conductivity, aesthetics and plasticity, which determine the scenarios in which each of them is applicable. 1. Density and weight Titanium alloy has a density of 4.54g/cm³, while aluminum alloy has a density of...
Titanium and titanium alloy wire rolling is to titanium and titanium alloy wire billet (into a disk or a single root) as raw material, through the drawing and get into a disk or a single root of the wire products, including titanium iodide wire, titanium-molybdenum alloy wire, titanium-tantalum alloy wire, industrial pure titanium wire and other titanium alloy wire. Titanium iodide wire is used in instruments, meters, electronics and other industrial sectors.Ti-15Mo alloy wire for vacuum...
Titanium tube annealing process details
First, the basic principle of titanium tube annealing process Titanium tube annealing is a heat treatment process, by heating the titanium tube to a certain temperature, and in a certain period of time to control the cooling rate to change the organizational structure and properties of titanium tube. Annealing can eliminate the stress of titanium tube processing, improve grain refinement, thereby improving corrosion resistance, strength and other performance parameters. Second, the flow of...
What are the fixing methods for titanium coils
There are two main fixing methods for titanium coils: detachable and non-detachable. The choice of these two types of fixing methods mainly depends on the specific application scenarios, the nature of the medium of the material and the corrosion of the titanium coil. First of all, let's look at the detachable fixing method. The greater advantage of this way is its flexibility. As the titanium coil may need to be used in the process of routine maintenance, overhaul and cleaning operations,...
How to tell if a screw is made of titanium
To determine whether the screws are made of titanium, you can refer to the following methods: 1. Appearance identification: observe the appearance of the screw. Pure titanium screws and titanium alloy screws are similar to traditional stainless steel, copper and iron screws, but the high-end series of titanium screws can reach a higher level. Its appearance is beautiful, sometimes like handicrafts emit a cool light. Compared with iron screws and copper screws, titanium screws will appear...
Titanium non-standard parts processing how to achieve high quality
Titanium non-standard parts processing to achieve high quality, can start from the following: 1. Design stage: Fully consider the needs and requirements of customers to ensure that the design of non-standard parts can meet specific functions and use scenarios. Considering the manufacturability and maintainability of non-standard parts, the design should reserve appropriate machining allowances and simplify the structure to facilitate processing and maintenance. 2. Material selection: Selection...
What are the product specifications and standards of titanium welded pipe?
Titanium welded pipe is a kind of special metal welding material, which is widely used in chemical industry, medicine, ship, aerospace and other fields due to its excellent corrosion resistance and high temperature strength. The product specifications and standards of titanium welded pipe mainly include the following aspects. I. Product specifications Outer diameter and wall thickness: the outer diameter and wall thickness of titanium welded pipe is its basic product specifications, according...
What are the ways of forging titanium materials?
Forging is a titanium metal billet (excluding plate) to apply external force, so that it produces plastic deformation, change size, shape and improve performance, used to manufacture mechanical parts, workpieces, tools or blanks of the molding process method. In addition, according to the slider movement there are slider vertical and horizontal movement (used in the forging of long and thin parts, lubrication and cooling and high-speed production of parts forging), the use of compensation...
What are the methods of surface treatment of non-standard bolts?
In the production process of non-standard bolts, it is very important to do a good job of surface treatment. Now let titanium standard parts manufacturers take you to understand. 1. Mechanical plating: by coating metal particles and cold welding the coating to the surface of the product, thus affecting the surface of the product. 2. Electroplating: Plated parts are immersed in an aqueous solution containing deposited metal compounds, and current is passed through the plating tank to...
Analysis of surface quality of titanium alloy machining
A common failure analysis Found in production, titanium alloy machining surface quality common failures over corrosion, hanging gray, oxide skin is not removed and streak-like splotch several kinds. 1, over corrosion Overcorrosion refers to the surface of the titanium alloy after pickling pits or unevenness and other defects, and material organization reveals a difference, generally leading to overcorrosion defects is due to the ratio of hydrofluoric acid and nitric acid is out of...
TA1,TA2,TC4,TA9 Titanium Rod Characteristics and Applications
Titanium's ability to be alloyed makes the metal stronger and more durable, and we provide you with a reliable metal that can withstand a variety of impacts. The strength of titanium rods depends on the material the titanium is made of, and here's how they differ: Pure titanium rods TA1, TA2, and TA3 are considered pure titanium. We offer pure titanium rods to meet the needs and expectations of a range of industries TA1 pure titanium rods Compared to other metal rods, TA1 titanium rods are the...
Titanium wire grades and classification of titanium wire
Pure titanium is a silver-white metal that has many excellent properties. Titanium's density is 4.54g/cm3, 43% lighter than steel, slightly heavier than the prestigious light metal magnesium. Mechanical strength is similar to steel, twice as big as aluminum, five times bigger than magnesium. Titanium is resistant to high temperatures, melting point 1942K, nearly 1000K higher than gold, nearly 500K higher than steel. Classification of titanium wire: Titanium wire is divided into: titanium wire,...
Characteristics of titanium tubing
1. Wall thickness of titanium tube Heat conduction tube wall thickness by the use of conditions, tube plate materials, expanding the construction capacity of the tube operation, the tube end of the welding technology, etc. to decide, due to the small diameter of the heat conduction tube, the strength of the requirements are not high, so the actual use of the tube with a thinner wall thickness, in general, such as copper alloy tubes with a wall thickness of 0.9mm-1.2mm; replace...
Titanium flange sealing surface type introduction
Titanium flange sealing face should be Z-optimized according to the different working conditions, media, pressure, specifications, temperature, etc., so there are different requirements for the flange. 1, FF-full flat sealing face (Flat Face Full Face), from the English better understand this type: sealing surface surface for the full flat. It is suitable for occasions where the pressure is not high and the medium is non-toxic. 2, RF - Raised Face sealing face (Raised Face), this type of...
The quality of titanium plates depends on the smelting process
Titanium plate has high corrosion resistance and specific strength, widely used in electric power, chemical industry, aviation parts, building materials, sports equipment, medical treatment and other fields, and is still expanding. Titanium plate has the advantages of low price, high performance, multi-functional, easy to produce and so on. The quality of titanium plate depends largely on the smelting process, including the chemical composition of titanium, the cleanliness of titanium water...
Deoxidizing and pickling of titanium rods and alloys
In the middle of heat treatment and after heat treatment most of the requirements for surface treatment in order to remove the metal surface oxide skin and various contaminants, reduce the activity of the metal bare surface, as well as in titanium and its alloys surface halogen coating protective layer and various functional coatings before and during the coating process, the application of such coatings is to improve the performance of the metal surface, for example, to prevent corrosion,...
What factors affect the quality of titanium alloy bar machining
The quality of titanium bar machining is affected by many factors. The following are some common factors: Material quality: the quality of titanium alloy bar directly affects the machining quality. The purity, organizational structure and mechanical properties of the material will affect the cutting performance and surface quality during machining. Cutting tool: the appropriate choice of tool is very important to the machining of titanium alloy bar. Titanium alloy has high cutting difficulty...
Analysis of the corrosion properties of titanium screws on motorcycle modifications
Titanium fasteners are a wide range of general-purpose basic parts, including titanium bolts, titanium screws, titanium studs, titanium nuts, titanium tapping screws, titanium washers, titanium retaining rings, titanium pins, titanium rivets and combinations of parts and other 12 categories, are widely used in general-purpose machinery, construction machinery and the defense industry and other fields. The quality and reliability of titanium fasteners play an important role in the work...
Analysis of bright spots in TC4 titanium alloy rods with low magnification organization
Titanium alloy has the advantages of low density, high specific strength, etc. It is widely used in aerospace field.TC4 titanium alloy has excellent comprehensive performance and is the two-phase titanium alloy with large dosage.The types of titanium alloy products can be divided into plates, rods, wires, tubes and anomalous forgings, etc., in which the production of rods accounted for about one-fifth of all kinds of titanium processed materials. TC4 titanium alloy bars can be used as engine...
Research and analysis of plastic deformation in the preparatory heat treatment of titanium elbow
Titanium elbow parts of the cold push-bending process is the production of such parts is quite economical, efficient process method, has a fairly important value of engineering applications. A study for the enterprise production of push-bending cracking problems, excluding the mold and push-bending machine suspected that the research point on the preparation of heat treatment process route to improve the plastic deformation capacity of the billet. Through the study, the following main...
The four laws of plastic deformation of titanium alloy forgings
Titanium forgings follow the following basic laws in plastic deformation: 1, the law of tangential stress Forging under the action of external forces, only when its internal shear stress reaches a critical value, it is possible to produce plastic deformation. The size of the critical shear stress depends on the type of forging (composition, organization) and deformation conditions (deformation temperature, degree of deformation, etc.) so the law of shear stress is related to plastic...
The four laws of plastic deformation of titanium alloy forgings
Titanium forgings follow the following basic laws in plastic deformation: 1, the law of tangential stress Forging under the action of external forces, only when its internal shear stress reaches a critical value, it is possible to produce plastic deformation. The size of the critical shear stress depends on the type of forging (composition, organization) and deformation conditions (deformation temperature, degree of deformation, etc.) so the law of shear stress is related to plastic...
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.